Leveling Your Brunswick 6100 Pool Table

The Brunswick Mod# AR-6100 Gold Crown is a regulation-size pool table, often found in bars. It is an eight-foot model with a one-piece slate, which can be tricky to level. To level the table, you will need a level tool, such as a bubble level or a digital level, and some wooden shims. You may also need a screwdriver. First, use the level tool to check if the table is balanced from end to end and from side to side. If it is not level, you will need to adjust the legs. The AR-6100 has adjustable legs with feet that can be screwed clockwise or counterclockwise to raise or lower the table. Make small adjustments and keep checking with the level tool until the table is level.

Use a carpenter's level to check for balance

To level a Brunswick 6100 pool table, you'll need a carpenter's level. This tool will help you determine whether the surface of the table is level, and if it's not, how much it deviates from being level.

Carpenter's levels come in various sizes, but for levelling a pool table, a 2-foot or 4-foot model should be sufficient. These levels typically have two or more vials filled with liquid and a bubble. When the level is placed on a flat surface, the bubble will be centred between two lines marked in the middle of the vial. If the surface is not level, the bubble will skew to one side.

To check for balance on your Brunswick 6100 pool table, follow these steps:

Step 1: Measure the Mid-line of the Pool Table

Place the carpenter's level in the middle of the pool table, oriented longways. This will help you determine if the table is balanced from end to end. If the table is level, the bubbles in the level will be centred in the vials. If the table needs adjustment, the bubbles will be above or below the middle lines, indicating that you need to raise or lower one of the shorter ends of the table.

Step 2: Measure the Shorter Mid-line of the Pool Table

Turn the level 90 degrees and place it in the middle of the table, oriented width-wise. This will help you measure the side-to-side level of the table. Again, adjust the table if the bubbles are not centred in the vials.

Step 3: Measure Each Side of the Pool Table

Place the level close to the edge of each of the four sides of the pool table to get more accurate readings. Most of the time, the issue with pool tables is that one leg is lower than the others. Move to each side and each corner of the table, checking with the level to identify the most uneven area.

Step 4: Fine-tune the Level

Once you've identified the problem area, make small adjustments to the legs of the table. You can do this by turning adjustable legs clockwise or counterclockwise, or by using shims—small, tapered pieces of wood—underneath the legs. After each adjustment, use the carpenter's level to check the balance of the table until you achieve a level surface.

It's important to note that pool tables don't need to be absolutely flat to be playable. Minor deviations from perfect level may not significantly affect gameplay, so don't get discouraged if you can't achieve absolute perfection.

Adjust the height of the table legs

To adjust the height of the legs of your Brunswick 6100 pool table, you'll first need to determine which corner or corners need to be adjusted. Place a carpenter's level on the table to check for any inconsistencies. Place the level in the center of the table, as well as on all four sides, to get a clear and accurate reading.

Once you've identified the lowest corner, you can begin to adjust the height of the legs. If your table has screw-in feet or legs, you can usually raise them by turning them to the right and lower them by turning them to the left. Always refer to the owner's manual to be sure. Make small adjustments and check the level after each one.

If your table doesn't have adjustable legs, you can use wooden shims to level it. Shims are small, tapered pieces of wood that can be placed under the legs to adjust the height. Place the shim under the leg and gently lower the foot onto it. Check the level after each shim you add to ensure you don't overdo it.

You may need to make several adjustments on different legs to get the table completely level. Don't be discouraged if it takes a bit of trial and error. Remember, pool tables don't need to be absolutely flat to be playable, so don't worry about getting it perfectly level.

Use a ball to check for balance

To level a Brunswick 6100 pool table, you can use a ball to check for balance. This method is a practical test of the table's balance, which can be carried out after making adjustments to the table legs or using shims to level the table.

To do this, simply roll the cue ball over a section of the table, as straight as possible. It is important to try to roll the ball as straight as you can, as this method is less accurate than using a carpenter's level. If you have one, you can use it to check your results.

Next, move your eye to be level with the plane of the table, so you are looking along the path of the ball. Observe whether the ball rolls off course towards one particular side of the table, or if it moves in a straight line.

Repeat this process on a few sections of the table. If the ball is rolling off course towards a particular side, you may need to adjust the table legs or use shims to level the table.

The Brunswick 6100 Gold Crown pool table is labelled as the finest Brunswick ever made by their own account. It is a regulation size table with a three-piece slate. The outside measurements are 63" by 114". The table features a ball return rail and tunnels, and the legs are individually adjustable for level.

Use a flat piece of glass and a marble to calculate balance

To level a Brunswick 6100 pool table, you can use a flat piece of glass and a marble to calculate the balance. This method does not require a traditional level and can help you determine if your pool table is level.

First, place a flat piece of glass in the middle of the pool table. Then, place a marble in the centre of the glass. If the pool table is level, the marble should remain in place. If the marble rolls off the glass towards one side of the table, you will need to adjust the legs of the table to make it level.

Repeat this process on every side of the table, placing the glass and marble 2 to 3 inches (5 to 7.6 cm) from each pocket. If the marble consistently rolls towards the same side of the table, that is the side you need to adjust.

The Brunswick 6100 is a regulation-size pool table with a three-piece slate. It is also known as the "Gold Crown" and is considered the finest Brunswick model ever made. Due to its size and construction, levelling this table can be tricky, and you may need to make adjustments to the legs or use shims for fine-tuning.

Using a flat piece of glass and a marble is just one way to check the balance of your pool table. You can also use a carpenter's level or a ball to check for practical balance. Remember to measure the mid-line of the table in both directions to ensure it is level from end to end and side to side.

Find the lowest corner

To find the lowest corner of your Brunswick 6100 pool table, you'll need a carpenter's level. Place the level on the table, oriented longways, to check if the table is balanced from end to end. Then, turn the level the other way, checking for balance from side to side.

Next, put the level close to the edge of each of the four sides of the table to get a more accurate reading. Move to each side and each corner of the table, checking with the level for the severity of the lean. The corner with the most lean is the lowest one.

If you don't have a carpenter's level, you can use a ball to check for balance. Roll the ball over a section of the table as straight as possible. If the ball rolls off course towards one particular side of the table, that's the lowest corner. Repeat this process on a few sections of the table.

Another way to check for the lowest corner without a level is to use a piece of glass and a marble. Place a marble in the middle of a piece of glass and set it in the centre of the table. The marble should stay in place if the table is level. If it rolls off the glass towards a particular area of the table, that's the lowest corner. Repeat this process with the glass and marble 2 to 3 inches from every pocket on the table.

Frequently asked questions